- #Free detune vst full#
- #Free detune vst plus#
Vowel - Resonant filter that can make spoken vowel type resonances ('AEIOU' vocal effect). The phasing is under the control of the Cutoff knob. Phaser 3 - Alternative, alternative phasing effect. Phaser 2 - Alternative phasing effect. Peak - Very narrow band of frequencies are allowed through at the Cutoff frequency (Boost narrow band of frequencies). Notch - Very narrow band of frequencies are cut at the Cutoff frequency (Cut a narrow band of frequencies). High shelf - Boost/cut all frequencies above the cutoff (like a Treble control). Low shelf - Boost/cut all frequencies below the cutoff (like a Bass control). Band pass 12 Alt - Band pass, 12 dB per octave slope, starting at the Cutoff frequency. Band pass 12 - Band pass, 12 dB per octave slope, starting at the Cutoff frequency. High pass 24 - High pass, 24 dB per octave slope, starting at the Cutoff frequency. High pass 12 Alt - High pass, 12 dB per octave slope, starting at the Cutoff frequency. 
High pass 12 - High pass, 12 dB per octave slope, starting at the Cutoff frequency. High pass 6 - High pass, 6 dB per octave slope, starting at the Cutoff frequency. Low pass 24 Alt - Low pass, 24 dB per octave slope, starting at the Cutoff frequency. Low pass 24 - Low pass, 24 dB per octave slope, starting at the Cutoff frequency. Low pass 12 Alt - Low pass, 12 dB per octave slope, starting at the Cutoff frequency. Low pass 12 - Low pass, 12 dB per octave slope, starting at the Cutoff frequency. Low pass 6 - Low pass, 6 dB per octave slope, starting at the Cutoff frequency. Res - Filter resonance, a peak at the cutoff frequency. Cutoff - Center frequency at which the filter acts. Source plugins include FLEX and Love Philter. Bit Crush: Higher values will add a crunchy, grainy quality to the sound.Ĭontrols shown on the module will change depending on the selected model. Higher values will reduce high-frequency fidelity and add 'aliasing' noises. Crusher - Rate Crush: Sample frequency. Distructor - Wave folder, Aperture and Abrasive. Harmor - Based on Harmor algorithms: Classic, Flathat, Cube, Log, Softsat, Rubber, Ribbon, Sincrush, Bitcrush and Bitjam. Blood overdrive - Based on Blood Overdrive. Distortion algorithms include those found in Harmor, Blood Overdrive, Fast Distortion, Soft Clipper, Waveshaper, Delay 3 (distortion, sample rate / bit depth), Transistor Bass and new algorithms - Wavefolder (folding distortion), Aperture (warping distortion), and Abrasive (noise modulation distortion). Controls shown on the module will change depending on the selected model. Overdrive distortion using classic and modern techniques. Show Peakmeters - So you can disable them and not get blinded by the flashy lights. Soft Clip Output - Applies soft clipping to the final output. Move Modules - Click the left/right arrows below Module slots. Out - Output level to the next module, or plugin output if it is in the far-right position in the rack. #Free detune vst full#
Mix - Left (0%) is dry and Right (100%) is the full wet mix of the effect.Click the + icon below an empty slot to add one. Add/Remove Modules - Click the gear icon at the bottom of the Module slots to remove modules.Switch (top) - Disable / enable the effect module.Signal flow is from left to right in the plugin. Most modules can have several models or algorithms (selected from the drop-down menus). Use 4x the same module or any combination of the four.
NOTE: Four slots are available with 4 modules. Then adds the filters from FLEX, Choruses from Delay 3 and wraps it all in Speaker Cabinets using Fruity Convolver.
#Free detune vst plus#
Distructor is a modular plugin that takes the distortion from, Harmor, Blood Overdrive, Fast Dist, Soft Clipper plus the Bit and Rate reduction from Delay 3.
0 kommentar(er)
